ISO/TS TECHNICAL SPECIFICATION 13399-405 First edition 2016-03-01 Cutting tool data representation and exchange - Part 405: Creation and exchange of 3D models - Collets Repreésentation et échange des données relatives aux outils coupants Partie 405: Creation et échange de modeles 3D - Pinces de serrage Reference number IS0/TS 13399-405:2016(E) ISO International Organization for Standardization @ IS0 2016 HEJIANG INST OF STANDARDIZATION C1 5956617 ed without license from IHS IS0/TS13399-405:2016(E) COPYRIGHTPROTECTEDDOCUMENT IS02016,PublishedinSwitzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISO's member body in the country of the requester. IsO copyrightoffice Ch. de Blandonnet 8 . CP 401 CH-1214 Vernier, Geneva, Switzerland Tel. +41 22 749 01 11 Fax +41 22 749 09 47 [email protected] www.iso.org PrganizationforStandardization ensee-ZHEJIANG INST.OF STANDARDIzARoISQ16- All rights reserved etworking permitted without license from IHS IS0/TS 13399-405:2016(E) Contents Page Foreword ..V Introduction. ..vii 1 Scope. 2 Normative references 3 Starting elements, coordinate systems, planes 3.1 General. .2 3.2 Reference system (PCS -primary coordinate system) 3.3 Mounting coordinate system. 2 3.4 Adjustment coordinate system at workpiece side 3.4.1 General. 3 3.4.2 Designation of coordinate systems at workpiece side ..3 3.4.3 Arrangement of coordinate system workpiece side 4 3.5 Planes. .5 4 Design of the model .6 4.1 General .6 4.2 Necessary properties for the connection interface feature. ..7 5 Double angle collet .7 5.1 General. .1 5.2 Necessary properties ..8 5.3 Basic geometry 5.4 Double angle collet, complete .9 6 Collet with straight shoulder .9 6.1 General 6.2 Necessary properties. ..10 6.3 Basic geometry .10 6.4 Completed collet with straight shoulder ..11 7 Short double angle collet ..11 7.1 General. .11 7.2 Necessary properties. ..12 7.3 Basic geometry. ..12 7.4 Completed short double angle collet ..13 8 Collet with elastic segments ..13 8.1 General ..13 8.2 Necessary properties .13 8.3 Basic geometry. .14 8.4 Completed collet with elastic segments. ..14 9 Collet with axial adjustment .15 9.1 General. .15 9.2 Necessary properties. ..15 9.3 Basic geometry ..15 9.4 Completed collet with axial adjustment. ..16 10 Draw-in collet with retaining thread and spanner flats ..17 10.1 General ..17 10.2 Necessary properties .17 10.3 Basic geometry ..18 10.4 Completed draw-in collet with retaining thread and spanner flats ..18 11 Draw in collet with retaining thread .19 .19 11.1 General. 11.2 Necessary properties. ..19 11.3 Basic geometry ..19 Intematinal oganzation @stS2016 - All rights reserved iii see=ZHEJIANG INST OF STANDARDIZATION C1 5956617 bvided by IHSunder license withISO vithoutlicense from IHS Not for Resale, 2016/4/26 02:47:10